What the SRVO-136 alarm means

The amplifier hardware detected an abnormal current condition. In field practice this points strongly to a failed servo amplifier power stage. This is a routine repair in our workshop for FANUC R-30iA / R-30iB / R-30iB Plus systems, and we normally pin it down during the first site check.

Most common causes

  • Servo amplifier power module failure (most likely)
  • Motor or cable short (rule out first)
  • Control power instability
Field note: Begin with the first item in the list; it has a far higher on-machine occurrence rate than the others.

Step-by-step field fix

  1. Megger-test motor and cable to rule out shorts
  2. Swap the amplifier with a known-good unit - alarm follows the amp = replace it
  3. After amp replacement, monitor motor temperature on the affected axis
Safety first: For FANUC srvo-136, amplifiers and boards are live parts: hot-plugging a board burns interface circuits, and body static can kill sensitive devices. What you can check yourself first is Megger-test motor and cable to rule out shorts; live boards and power devices handling is not a DIY job.

How we diagnose amplifier/hardware alarms on site

FANUC srvo-136 belongs to the amplifier & hardware family. On FANUC srvo-136 the failing stage is alpha-i / beta-i servo amplifiers with PSM supply modules and SVM servo modules (SPM where spindles fit) on the R-30iB Plus / R-30iB Mate Plus / R-30iA - the amplifier and drive hardware itself plus its periphery: boards, fuses, cooling, supply, connectors and self-test. We start reading FANUC srvo-136 at the iPendant ALARM screen (SRVO / MOTN / SYST / INTF prefixes) together with the amplifier's 7-segment status code.

The chain involved in FANUC srvo-136 runs: control-side signal -> amplifier board (drive and sense circuits) -> fuses and supply -> cooling -> motor-side output.

When FANUC srvo-136 fires, clear the external causes first - Many hardware alarms are not hardware at all but external conditions: a packed filter causing over-temperature, a missing phase causing undervoltage, a loose connector causing a communication drop. Our order clears the externals first - clean, replace the mat, measure supply, re-seat terminals - near-zero cost and a high hit rate. Only when externals are gone do we judge boards or power stage. It also keeps the quotation honest: we do not sell parts we have not earned.

Field notes on this page cover FANUC srvo-136 (DCLVAL Alarm (Group / Axis)); written by the Henghuan repair team, updated 2026-10-01.

Stalled on the diagnosis? Let an engineer help remotely

Give us the alarm code, robot model and the action at the moment of the alarm, and our engineers can give you a quick read — phone or video remote diagnosis is free.

Get a Free Remote Diagnosis See Repair Services

Hotline: +86-20-39029800 · WhatsApp: +86-188-1886-2860

Related Amplifier & Hardware alarms

SRVO-057 — FSSB Disconnect SRVO-068 — DTERR - Data Transmission Error SRVO-069 — CRCERR - CRC Error SRVO-071 — SPHAL - Soft Phase Alarm SRVO-072 — PMAL - Pulse Coder Phase Alarm SRVO-073 — CMAL - Pulse Coder Count Error
Same family: this code belongs to the Amplifier & hardware alarms family - the page collects all Amplifier & hardware-family codes we have handled, with the common inspection order and spares.
Other brands: see our KUKA, ABB, Yaskawa and Universal Robots field-fix libraries — or the full 10-brand hub.

Frequently asked questions

QWhat does the FANUC srvo-136 alarm mean?

The amplifier hardware detected an abnormal current condition. In field practice this points strongly to a failed servo amplifier power stage. This is a routine repair in our workshop for FANUC R-30iA / R-30iB / R-30iB Plus systems, and we normally pin it down during the first site check. FANUC srvo-136 sits in the amplifier & hardware family; on our work orders the highest-frequency trigger for this code is "Servo amplifier power module failure (most likely)".

QCan I clear a FANUC srvo-136 alarm myself?

Whether FANUC srvo-136 clears on its own depends on the outcome of "Megger-test motor and cable to rule out shorts". Finish the flow with "After amp replacement, monitor motor temperature on the affected axis" to confirm FANUC srvo-136 - do not skip it. If that step is clean, the second most frequent cause on FANUC srvo-136 is "Motor or cable short (rule out first)". Two attempts and still there means stop: FANUC srvo-136 involves live boards and power devices, and running FANUC srvo-136 on can turn a repairable fault into a replacement.

QFor hardware alarms like FANUC srvo-136, does it always mean an expensive part swap?

The commonest causes we see on FANUC srvo-136 are "Servo amplifier power module failure (most likely), Motor or cable short (rule out first), Control power instability", so we stock the van against those. For FANUC srvo-136 specifically, we carry fuses, filter mats, common connectors and terminals; boards are stocked by type or go through the repair channel. For FANUC srvo-136, on hardware alarms we inspect before quoting - we do not open with replace the power stage. Before we roll, tell us what FANUC srvo-136 shows on the iPendant ALARM screen (SRVO / MOTN / SYST / INTF prefixes) together with the amplifier's 7-segment status code and what the machine was doing - phone or video triage is free.

This page on FANUC srvo-136 is based on the field experience of the Henghuan Robotics repair team. Alarm explanations are our own summary for troubleshooting reference and may differ across controller and software versions — if unsure, verify against FANUC documentation or reach out to us. Henghuan is an independent service provider with no affiliation or endorsement by FANUC.